ODROID-HC4 is new Home-Cloud platform based on the same ARM CPU as the ODROID-C4. We adopted a 12nm fabricated energy efficient 1.8Ghz Cortex-A55 quad core processor with faster 4GB DDR4 RAM. A 16MiB SPI flash chip exists.

Specifications:

FORM FACTOR	Board Dimensions: 84mm x 90.5mm x 25.0mm Heatsink Dimensions: 40mm x 32mm x 10mm Weight: 280g including heatsink, fan and case
PROCESSOR	Amlogic S905X3 Processor L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processorsQuad-Core Cortex-A55 (1.800GHz) ARMv8-A architecture with Neon and Crypto extensions Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz)
MEMORY	DDR4 4GiB with 32-bit bus width Data rate: 2640 MT/s (PC4-21333 grade) 1.2Volt low power design
STORAGE	1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
NETWORKING	1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps) – Realtek RTL8211F (Ethernet transceiver) – LED indicators * Green LED: Flashing by data traffics at 100Mbps connection * Amber LED: Flashing by data traffics at 1000Mbps connection
VIDEO	1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
AUDIO	1 x HDMI digital output
COOLER	1 x Passive heatsink ( 40x32x10 mm ) on the CPU of PCB board 1 x Hydraulic Bearing FAN – Rated Voltage : 5V – Rated Current : 100mA – Max Speed RPM : 4,000 – Air Flow CFM : 4.3 – Air Pressure (In H2O) : 0.053 – Noise Level(dBA) : 23.9 – Dimension : 40 x 40 x 10.6 mm – Wire & Connector : 80mm, 4 pin 1.25mm pitch
EXTERNAL I/O	1 x USB 2.0 host port 1 x Debug serial console (UART) 2 x SATA Connectors OTHER FEATURES IR receiver for remote controller System LED Indicators: – Red (POWER) – Solid light when DC power is connected – Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
OTHER FEATURES	IR receiver for remote controller System LED Indicators: – Red (POWER) – Solid light when DC power is connected – Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
POWER	1 x DC jack : outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm DC input : 14.5V ~ 15.5V – DC 15V/4A power adaptor is recommended. Sold separately. Power consumption with two ST2000DM006 HDDs : – IDLE(with HDD in spin-down) : ≃ 5.88W – Active(using SAMBA): ≃ 15.59W – Suspend: ≃ 0.29W

Note:

The supplier of the product has no replacement and/or refund policy as part of their product warranty/guarantee. Furthermore, the repair cost and the cost of shipping to and fro from South Korea has to be borne. As Fab.to.Lab is merely an intermediary we extend the exact same warranty terms to all customers of Harkernel.

Please find more details here: Supplier warranty terms and conditions: https://www.hardkernel.com/agreement/

Documents: