Hantek DSO2000 Series Oscilloscope is a Cost-effective economy oscilloscope, 150MHz Bandwidth, 1GSa/s, 8M memory depth; with 1CH 25MHz waveform generator, support arbitrary waveform output.

Features:

2 channels which are respectively controlled by independent knobs
100 MHZ and 150MHZ analog channel bandwidth
Sampling rate up to 1 GSa/s
8M memory depth
Vertical range 2mV/div ~ 10V/div
Vertical resolution: 8bit
Trigger: Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
BUS decode and protocol analysis: RS232/UART, I2C, SPI, CAN, LIN
Can save multiple data formats, such as settings, waveforms, reference waveforms, CSV, pictures
A 3-digit digital voltage meter and a 6-digit hardware frequency indicator
32 kinds of auto measurements with statistics, real-time statistics of maximum, minimum, standard deviation and etc.
2 sets of digital voltmeters
Support threshold testing, free measurements within the screen
Abundant SCPI remote command control
USB Host/Device

Specifications:

Model: DSO2C15 / DSO2C10
Bandwidth: 150MHz / 100MHz
Sample rate: 1GSa/s (single channel), 500MSa/s (two channels)
Normal sample data
Peak-to-peak value: Display high frequency and random burr
Average: Average waveform, times: 4, 8, 16, 32, 64, 128
High resolution: Up to 12bit
Input coupling: DC, AC, GND
Input impedance: 1MΩ±2% ‖ 20pF±3pF
Probe attenuation factor: 1X, 10X, 100X, 1000X
Voltage rating: 300V CAT II
Maximum input voltage: 300VRMS (10X)
Waveform interpolation: (sin x)/x
Maximum record length: Single channel maximum 8M; two channels maximum 4M
Horizontal scale range: 2ns/div~100s/div, 1, 2, 5 step by step
Time base mode: Y-T, X-Y, Roll
Zero offset: ±0.5 div × minimum time base gear
Sample Rate and Delay Time Accuracy: ±25ppm
Delta Time Measurement Accuracy (Full Bandwidth): Single-shot, Normal mode ±(1 sample interval + 100ppm×reading + 0.6ns)
>16 times averages: ±(1 sample interval + 100ppm×reading + 0.4ns)
Sample interval: sec/div ÷ 200
Sample Rate and Delay Time Accuracy: ±50ppm (at any interval greater than 1ms)
Rising time in BNC position: 2.4ns / 3.5ns / 2.4ns / 3.5ns
Vertical resolution: 8 bits resolution, each channel samples simultaneously
Vertical sensitivity: 2mV/div to 10V/div
Offset range: ≥200mV/div, ±1V; <200mV/div, ±50V
Mathematical operation: +, -, ×, ÷, FFT
FFT windows: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop
Bandwidth limit: 20MHz
Bass response (-3dB): In BNC position ≤10Hz
Vertical gain accuracy: 10V/div to 10mV/div ±3%; 5mV/div to 2mV/div ±4%
Note: Bandwidth reduced to 6MHz when using a 1X probe
Trigger type: Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
Trigger level range: ±5 divisions from the center of the screen
Trigger mode: Auto, Normal, Single
Level CH1~CH2: ±4 divisions from the center of the screen
EXT: 0~3.3V
Holdoff range: 8ns~10s
Trigger level accuracy CH1~CH2: 0.2 div × volts/div within ±4 divisions from the center of the screen
EXT trigger level accuracy: ±(Set value × 6% + 40mV)
Edge trigger slope: Rising edge, falling edge, rising or falling edge
Edge trigger signal source: CH1, CH2, EXT
Pulse width trigger polarity: Positive polarity, negative polarity
Pulse width trigger condition: <, >, !=, =
Pulse width trigger signal source: CH1~CH2
Pulse width range: 8ns~10s
Pulse width accuracy: 8ns
Video trigger signal standard: NTSC, PAL
Video trigger signal source: CH1~CH2
Video synchronization: Scanning line, line number, odd field, even field, all field
Slope trigger slope: Rising, falling
Slope trigger condition: <, >, !=, =
Slope trigger signal source: CH1~CH2
Slope trigger time range: 8ns~10s
Slope trigger accuracy: 8ns
Overtime trigger signal source: CH1~CH2
Overtime trigger polarity: Positive polarity, negative polarity
Overtime trigger time range: 8ns~10s
Overtime trigger accuracy: 8ns
Window trigger signal source: CH1~CH2
Pattern trigger pattern: 0: low level; 1: high level; X: ignore
Pattern trigger level: CH1~CH2
Interval trigger slope: Rising, falling
Interval trigger condition: <, >, !=, =
Interval trigger signal source: CH1~CH2
Interval trigger time range: 8ns~10s
Interval trigger accuracy: 8ns
Under Amp trigger polarity: <

Oscilloscope Specifications
Sample Rate	1GSa/s (single channel) 500MSa/s (two channels)
Display Type	7'' diagonal TFT liquid crystal, dot, vector
Record Length	Single channel maximum 8M, Two channels maximum 4M
Analog Channel	2
Bandwidth	100MHz, 150MHz
Resolution	Vertical resolution 8bit
Electrical Specifications
Output Voltage	typical about 2Vpp input ≥1MΩ load
Output Power	Power supply:100-120VACRMS(±10%), 45Hzto 440Hz, CATⅡ, 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ
Maximum Operating Temperature	0~50 °C (32~122 °F)
Physical Attributes
Weight	1900g
Size	318 x 110 x 150mm (length x width x height)