• Your shopping cart is empty!

Hantek DSO2000 Series Oscilloscope is a Cost-effective economy oscilloscope, 150MHz Bandwidth, 1GSa/s, 8M memory depth; with 1CH 25MHz waveform generator, support arbitrary waveform output.
 
Features:
  • 2 channels which are respectively controlled by independent knobs
  • 100 MHZ and 150MHZ analog channel bandwidth
  • Sampling rate up to 1 GSa/s
  • 8M memory depth
  • Vertical range 2mV/div ~ 10V/div
  • Vertical resolution: 8bit
  • Trigger: Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
  •  BUS decode and protocol analysis: RS232/UART, I2C, SPI, CAN, LIN
  • Can save multiple data formats, such as settings, waveforms, reference waveforms, CSV, pictures
  • A 3-digit digital voltage meter and a 6-digit hardware frequency indicator
  • 32 kinds of auto measurements with statistics, real-time statistics of maximum, minimum, standard deviation and etc.
  • 2 sets of digital voltmeters
  • Support threshold testing, free measurements within the screen
  • Abundant SCPI remote command control
  • USB Host/Device
 
Specifications:
 
Model DSO2C15 DSO2C10
Bandwidth 150MHz 100MHz
Sample rate 1GSa/s (single channel) 500MSa/s (two channels)
Normal Sample data
Peak-to-peak value Display high frequency and random burr
Average Average waveform, times:  4, 8, 16, 32, 64, 128
High resolution Up to 12bit
Input coupling DC, AC, GND
Input impedance 1 MΩ±2% ‖20pF±3pF
Probe attenuation  factor 1X, 10X, 100X, 1000X
Voltage rating 300V CAT II
Maximum input voltage 300VRMS (10X)
Waveform interpolation (sin x)/x
Maximum record length Single channel maximum 8M
Two channels maximum 4M
Horizontal scale range 2ns/div~100s/div  1, 2, 5 step by step
Time base mode Y-T, X-Y, Roll 
Zero offset ±0.5 div×minimum time base gear
Sample Rate and Delay Time Accuracy ±25ppm
Delta Time Measurement Accuracy (Full Bandwidth)Sample Rate and Delay Time Accuracy single-shot, Normal mode   ±（1 sample interval+100ppm×reading+0.6ns）
＞16 times averages ±（1 sample interval+100ppm×reading+0.4ns）
Sample interval=sec/div÷200
Sample Rate and Delay Time Accuracy ±50ppm（at any interval greater than 1ms
Rising time in BNC position (typical) 2.4ns 3.5ns 2.4ns 3.5ns
Vertical resolution 8 bits resolution, each channel samples simultaneously
Vertical sensitivity 2mV/div to 10V/div
Offset range ≥ 200mV/div, ±1V;
＜200mV/div ±50V
Mathematical operation +, -, ×, ÷, FFT
FFT Window: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop
Bandwidth Limit 20MHz
Bass response（-3db） In BNC position ≤ 10Hz
Vertical gain accuracy In ''normal''  or ''average'' acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%;
In ''normal'' or ''average'' acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4%
Note: Bandwidth reduced to 6MHz when using a 1X probe
Trigger type Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
Trigger level range  ±5 divisions from the center of the screen
Trigger mode Auto, Normal, single
Level CH1~CH2 ±4 divisions from the center of the screen
EXT 0~3.3V
Holdoff range 8ns~10s
Trigger level accuracy CH1~CH2 0.2 div×volts/div within ±4 divisions from the center of the screen
EXT ±（Set value× 6%+40mV）
Edge trigger Slope Rising edge, falling edge, rising or falling edge
Signal source CH1, CH2, EXT
Pulse width trigger Polarity Positive polarity, negative polarity
Condition(When) <, >, !=, =
Signal source CH1~CH2
Pulse width range 8ns ~ 10s
Accuracy 8ns
Video trigger Signal standard NTSC, PAL
Signal source CH1~CH2
Synchronization S canning line, line number, odd field, even field, all field
Slope trigger Slope rising, falling
Condition(When) <, >, !=,  =
Signal source CH1 ~ CH2
Time range 8ns ~ 10s
Accuracy 8ns
Overtime trigger Signal source CH1~CH2
Polarity Positive polarity, negative polarity
Time range 8ns ~ 10s
Accuracy 8ns
Window trigger Signal source CH1~CH2 
Pattern trigger Pattern 0: low level; 1: high level; X: ignore
Level（signal source) CH1~CH2
Interval trigger Slope rising, falling
Condition(When) <, >,  !=,  =
Signal source CH1~CH2
Time range 8ns ~ 10s
Accuracy 8ns
Under Amp trigger Polarity <
Oscilloscope Specifications
Sample Rate 1GSa/s (single channel) 500MSa/s (two channels)
Display Type 7'' diagonal TFT liquid crystal, dot, vector
Record Length Single channel maximum 8M, Two channels maximum 4M
Analog Channel 2
Bandwidth 100MHz, 150MHz
Resolution Vertical resolution 8bit
Electrical Specifications
Output Voltage typical about 2Vpp input ≥1MΩ load
Output Power Power supply:100-120VACRMS(±10%), 45Hzto 440Hz, CATⅡ, 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ
Maximum Operating Temperature 0~50 °C (32~122 °F)
Physical Attributes
Weight 1900g
Size 318 x 110 x 150mm (length x width x height)

Write a review

Please login or register to review

Hantek DSO2000 Series DSO2C10 / DSO2C15 Oscilloscope without Waveform generator

  • Brand: Hantek
  • Product Code: HTK-DSO2000-Scope
  • Reward Points: 208
  • Availability: In Stock

  • रo 20,663.00

  • Price in reward points: 20829
  • 2 or more रo 20,496.00
  • 5 or more रo 20,329.00
  • 9 or more रo 20,163.00

Available Options


0 reviews / Write a review

Related Products

Tektronix TBS2000B Series TBS2072B / TBS2102B / TBS2202B Oscilloscope : 2 GS/s sample rate, 2-channel

Tektronix TBS2000B Series TBS2072B / TBS2102B / TBS2202B Oscilloscope : 2 GS/s sample rate, 2-channel

The TBS2000B Series of Oscilloscopes with a 9-inch WVGA display, 5 million point record length and 2..

रo 105,000.00

Tektronix TBS1000C Series TBS1052C / TBS1072C / TBS1102C / TBS1202C Oscilloscope : 1 GS/s sample rate, 2 Channel

Tektronix TBS1000C Series TBS1052C / TBS1072C / TBS1102C / TBS1202C Oscilloscope : 1 GS/s sample rate, 2 Channel

The TBS1000C Series Digital Storage Oscilloscope offers affordable performance in a compact design. ..

रo 40,200.00

Tags: Hantek, DSO2000, Oscilloscope

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments